How to Install Indian Challenger Inner Speaker Grill Covers (2019–2025)

Upgrading your Indian Challenger's inner speaker grill covers is one of the easiest ways to personalize your fairing and make your bike stand out. This guide walks you through the complete installation process using your Brock Black Designs custom grill set — no drilling, no cutting, just a clean swap in minutes.

Before You Begin

Inspect the kit and all components to confirm all parts are present and undamaged. If anything is missing or damaged:

• Purchased from a dealer: Contact your Selling Dealer for assistance.
• Purchased online: Contact Brock Black Designs customer service at 208-705-0028 (US & Canada only).

Fitment / Compatibility

These inner speaker grill covers fit 2019 and later Indian Challenger models, including:

• Indian Challenger
• Indian Challenger Dark Horse
• Indian Challenger Limited
• Indian Challenger Elite

Verify fitment for your specific model year at brockblackdesigns.com.

Tools Required

• Safety glasses
• Non-marring pry tool (plastic trim removal tool)

Important Notes Before You Start

• Do not pry between the speaker grille and the inner fairing — this will damage the paint.
• Use care around the speaker when using the non-marring tool.
• The new speaker grilles are side-specific — left and right are not interchangeable. Confirm orientation before installing.

Step-by-Step Installation

Step 1 – Power Down the Motorcycle

Turn the key or ignition switch to the OFF position and remove the key. If your Challenger is equipped with a keyless fob, move the fob away from the vehicle before starting work.

Step 2 – Secure the Bike

Park the motorcycle on a flat, stable surface. Fully extend the kickstand and confirm the bike is stable before proceeding. Put on your safety glasses.

Step 3 – Remove the Factory Speaker Grille

Using your non-marring pry tool, carefully work around the edge of the factory inner speaker grill to release the retaining clips. Insert the pry tool between the grill and the fairing panel and apply gentle, even pressure to pop each clip free without scratching the fairing.

Tip: Work slowly and feel for each clip releasing. Rushing can break a clip or scratch the surrounding panel.

Step 4 – Save the Gasket and Clips

Once the factory grill is free, carefully remove the gasket and retaining clips from the old grill. These are reused with your new Brock Black Designs grill cover — set them aside in a safe place.

Step 5 – Pre-Fit the New Grill (Dry Run)

Hold the new grill up to the speaker opening without the gasket to verify fitment and confirm it is the correct side (left vs. right). It will feel slightly loose without the gasket — that's normal. Remove and set aside once confirmed.

Step 6 – Transfer Gasket and Clips to the New Grill

Fit the gasket and clips onto your new custom grill cover in the same positions they came off. Make sure the gasket seats flush and is not twisted or bunched anywhere around the perimeter.

Step 7 – Install the New Grill Cover

Align the new grill cover with the speaker opening in the fairing. Press firmly and evenly around the edges until all clips click into place. You should hear and feel each clip seat — if a section feels loose, press again until it snaps in.

Step 8 – Repeat on the Other Side

Follow the same process for the second speaker grill. Step back and check that both covers are flush with the fairing and the designs are oriented consistently side to side.

Step 9 – Final Check

Give each grill a firm tug to confirm all clips are fully seated. Wipe off any fingerprints with a clean microfiber cloth. You're done!

Tips for a Perfect Install

• Work in good lighting so you can see the clip positions clearly.
• A plastic trim removal tool (non-marring pry tool) is essential — metal tools will scratch your fairing.
• If a clip feels stiff, warm the area slightly with a heat gun on low for 10–15 seconds to make the plastic more pliable.
• Watch the full install video at the top of this page for a visual walkthrough.

Shop Indian Challenger Speaker Grill Covers

Browse our full lineup of custom inner speaker grill covers for the 2019–2025 Indian Challenger:

• USMC Themed Inner Speaker Grills Set
• Warrior Themed Inner Speaker Grills Set
• Ancient Skull Themed Inner Speaker Grills Set
• Spartan Themed Inner Speaker Grills Set
• Sergeant Stripes Themed Inner Speaker Grills Set

Questions? Call us at 208-705-0028 or send us a message — we're happy to help.